日本三菱柴油機、柴油發電機、工程機械、船舶動力系統中英文技術詞匯

negative valve terminal；負值接線柱

negative-positive-negative；負－正－負

neglect；忽略，省略，疏忽

neglected setting；放棄調整

negotiate；讓購，兌現，協商

neon；氖，霓紅燈

neon lamp；氖燈

neoprene；氯丁橡膠，合成樹膠，聚氯丁橡膠

neoprene pad；氯丁橡膠墊

nest；座，巢，加入

net；網，純凈，要點

net horsepower；凈馬力

net result；最終結果

network；網，網格，電路

network operation；網絡操作

network resistor；電阻

neut；中和的，中性的，中立的

neutral；中性的，中立的，空檔

neutral adjustment；空檔調整

neutral adjustment procedure；空檔調整步驟

neutral adjustment screw；空檔調整螺釘

neutral adjustment screw location；空檔調整螺釘位置

neutral area；空檔區

neutral assembly bar；空檔總成桿

neutral button；空檔按鈕

neutral check；空檔檢查

neutral circulation；空檔運行

neutral connection；空檔連接

neutral contact；中性接觸

neutral control button；空檔操縱按鈕

neutral delivery；空檔傳送

neutral detent；空檔卡銷

neutral detent position；空檔卡銷位置

neutral directional range；空檔方向范圍

neutral flow；中性流

neutral flux；中性

neutral ground circuit；中性點接地電路

neutral indicator light；空檔指示器燈

neutral lead；空檔導線

neutral lock；空檔鎖

neutral lock button；空檔鎖按鈕

neutral lock control；空檔鎖操縱機構

neutral lock lever；空檔鎖桿

neutral lock parking brake lever；空檔停放制動器鎖桿

neutral locked position；空檔鎖定位置

neutral mechanism；空檔機構

neutral opening；空檔口

neutral operation；空檔操作

neutral or in-gear signal；空檔或掛檔信號

neutral panel control；空檔面板控制

neutral port；中立港

neutral position；空檔位置

neutral position adjustment；空檔位置調整

neutral range；空檔范圍

neutral screw；空檔螺釘

neutral screw adjustment procedure；空檔螺釘調整步驟

neutral setting；空檔調整

neutral slot；空檔槽

neutral speed；空檔速度

neutral speed position；空檔速度位置

neutral spring；空檔彈簧

neutral start；空檔起動

neutral start adjustment；空檔起動調整

neutral start circuit；空檔起動線路

neutral start control；空檔起動操縱

neutral start control circuit；空檔起動操縱線路

neutral start control ground；空檔起動操縱接地

neutral start control input；空檔起動操縱輸入

neutral start control module；空檔起動操縱模塊

neutral start control pin；空檔起動操縱軸

neutral start dead zone；空檔起動死區

neutral start provision；空檔起動裝置

neutral start relay；空檔起動繼電器

neutral start relay socket；空檔起動繼電器插座

neutral start switch；空檔起動開關

neutral start switch adjustment；空檔起動開關調整

neutral start switch adjustment procedure；空檔起動開關調整過程

neutral start switch adjustment section；空檔起動開關調整部分

neutral start switch assembly；空檔起動開關總成

neutral start switch component；空檔起動開關零部件

neutral start switch operation；空檔起動開關操作

neutral start switch pin；空檔起動開關銷

neutral start system；空檔起動系統

neutral steer belt；空檔操向帶

neutral switch；空檔開關

neutral symbol；空檔標記

neutral travel；空檔行駛

neutral travel position；空檔行駛位置

neutral wire；零線

neutral zone；中性區，緩沖帶

neutral-1；空檔－１

neutral-2；空檔－２

neutral/run switch；空檔/運行開關

neutral/run switch circuit；空檔/運行開關電路

neutral/run switch terminal；空檔/運行開關接線柱

neutralization；補償，中和，抵消

neutralize；中和，抵消，中立化

neutralizer；中和液，平衡器，空檔器

neutralizer ball check；空檔器球狀物檢查

neutralizer button；空檔器按鈕

neutralizer button switch；空檔器按鈕開關

neutralizer finger；空檔器指針

neutralizer function；空檔器作用

neutralizer group；空檔器組件

neutralizer housing；空檔器殼體

neutralizer manifold；空檔器歧管

neutralizer screw；空檔器螺釘

neutralizer solenoid；空檔器螺線管

neutralizer solution；中和劑溶液

neutralizer stem；空檔器桿

neutralizer switch；空檔器開關

neutralizer switch conversion group；空檔器開關變換組件

neutralizer valve；空檔器閥

neutralizer valve adjustment；空檔器閥調整

neutralizer valve arrangement；空檔器閥布置

neutralizer valve body；空檔器閥體

neutralizer valve drain line arrangement；空檔器閥排放管布置

neutralizer valve group；空檔器閥組

neutralizer valve operation；空檔器閥操作

neutralizer valve passage；空檔器閥通路

neutralizer valve solenoid；空檔器閥線圈

neutralizer valve spool；空檔器滑閥

neutralizer valve spring；空檔器閥彈簧

neutralizer valve stem；空檔器閥桿

neutralizer valve stop bolt；空檔器閥銷螺栓

neutralizing brake pedal；空檔制動踏板

neutralizing function；中和作用

neutralizing solution；中和溶液

neutron；中子

new；新的，現代的，新造的

new scroll；新的渦形管

new scroll (ns)；新的渦形管

new scroll fuel system；新渦形管燃油系統

newly；新近，最近，重新

newly selected gear；重新選擇的齒輪

newton；牛頓

newton meter；牛頓(米

next；其次，然后，緊接[在后面]的

nf；美制細牙螺紋

nf bolt；美制細牙螺紋螺栓

nf guide bolt；美制細牙螺紋導向螺栓

nf thread；美制細牙螺紋

nfpa form number；美國國家防火學會文件號，全國流體動力學會文件號

ngeo；ｘｘｘ

nicad；鎳鎘蓄電池

nickel；鎳，自然鎳，鎳灰

nickel cadmium；鎳鎘

nickel-cadmium battery；鎳鎘蓄電池

nickel-cadmium battery pack capacity；鎳鎘蓄電池組容量

nine valve control bank；九閥操縱邊

nine-pin connector；九芯連接器，九針插座

ninth speed；九速

nipple；噴嘴，潤滑嘴，螺紋接頭

nipple assembly；噴嘴總成

nipple portion；噴嘴部分

nitrate；硝酸鹽，硝化，硝酸

nitration；硝化[作用]，硝化反應

nitration product；硝基產物

nitration rate；硝化率

nitrided；氮化，滲氮

nitrided crankshaft；滲氮曲軸

nitrite；亞硝酸鹽[酯]，硝石

nitrogen；氮，氮氣

nitrogen actuator；氮致動器

nitrogen actuator cylinder；氮致動器氣缸

nitrogen bottle；氮氣瓶

nitrogen chamber；氮氣艙〔室〕

nitrogen charge；充氮

nitrogen charge valve；充氮閥

nitrogen charged accumulator；充氮蓄能器

nitrogen charged dimension；充氮體積

nitrogen charging；充氮

nitrogen charging apparatus；充氮設備

nitrogen charging arrangement；充氮裝置

nitrogen charging chuck；充氮夾具

nitrogen charging cylinder；充氮缸

nitrogen charging equipment；充氮設備

nitrogen charging group；充氮裝置組件

nitrogen charging group box assembly；充氮組件箱總成

nitrogen charging group connection；充氮裝置組件連接

nitrogen charging procedure；充氮步驟

nitrogen charging tool；充氮工具

nitrogen charging valve；充氮閥

nitrogen container；氮氣罐

nitrogen cylinder；氮缸

nitrogen cylinder actuator；氮缸致動器

nitrogen cylinder actuator lever；氮缸致勸器杠桿

nitrogen cylinder actuator plunger；氮缸致動器滑閥〔柱塞〕

nitrogen cylinder valve；氮缸閥

nitrogen gas；氮氣

nitrogen gas charge；充加氮氣

nitrogen gas charging fitting；充氮裝置接頭

nitrogen gas cylinder；氮缸

nitrogen gas pressure氮氣壓力

nitrogen inflated tire；充氮輪胎

nitrogen inflation；充氮

nitrogen inflation equipment；充氮設備

nitrogen inflation group充氮(設備)組件

nitrogen inflation information；充氮信息〔資料〕

nitrogen precharge；預先充氮

nitrogen precharge pressure；預充氮壓力

nitrogen preload pressure；氮氣預加壓力

nitrogen pressure；氮氣壓力

nitrogen pressure charge；氮氣加壓充灌

nitrogen regulator；氮氣調節器

nitrogen supply；氮的供給

nitrogen suspension system；氮氣懸掛系統

nitrogen tank valve；儲氮罐閥

nitrogen tire inflation group；氮氣輪胎充氮裝置組件

nitrogen valve；氮氣閥

nitrogen valve location；氮氣閥位置

nitrous；亞硝酸的

nlgi；國家潤滑脂研究所

nlq；xxx

nls；非線性系統

nls contact；非線性系統的接觸

no flashing procedure；無閃爍程序

no load current；空載電流

no-fuel position；無(燃)油位置

no-load condition；空載狀態

no-load engine speed；空載發動機轉速

no-load engine speed signal；空載發動機轉速信號

no-load rpm；空載轉速，轉/分

no-load situation；空載狀態

no-load speed；空載速度

no-load test；空載試驗

no-load voltage；空載電壓

no-load voltage adjustment；空載電壓調整

no-lug application；非抓地板的應用

no-slip condition；非滑動狀態

no-spin differential；非自旋差速器

no-spin differential assembly；非自旋差速器總成

no-spin differential check；非自旋差速器檢查

no-spin differential component；非自旋差速器部件

no-spin differential group；非自旋差速器組件

nodular iron；球墨鑄鐵

nodular iron adapter；球墨鑄鐵管接頭

nodular iron spark plug adapter；球墨鑄失火花塞接頭

noise；噪聲

noise interference；噪聲干擾

noise level；噪聲級

noisy；有噪聲的，有干擾的

noisy vibratory mechanism；噪聲振動機理

nomenclature；術語

nominal；標稱的，名義的

nominal amplitude；名義振幅〔射程〕

nominal angular difference；標稱角度差

nominal bore；標稱孔

nominal bushing inside diameter；套筒標稱內徑

nominal calibration factor；標稱校準因數

nominal clearance；標稱間隙

nominal dead band；標稱非靈敏區

nominal dimension；標稱尺寸

nominal distance；標稱距離

nominal dog clutch engagement；標定爪牙離合器接合

nominal engine speed；發動機標稱轉速

nominal figure標定值[圖形]

nominal fit；標準配合

nominal flow rating；額定流率

nominal full stroke current；最大行程下額定電流

nominal mounting distance；標稱安裝距離

nominal oil capacity；油標稱容量

nominal output；額定輸出

nominal pin diameter；銷標稱直徑

nominal piston travel；活塞標稱位移

nominal pressure；額定壓力

nominal pressure drop；額定壓力降

nominal retraction；名義收縮(力)

nominal rupture pressure名義破壞壓力

nominal specification；標準技術規格

nominal value；額定值

nominal voltage；額定電壓

nominal working pressure；額定工作壓力

nominally；標稱，名義上

non-european light；非歐洲人的處世標準[見解]

nonadjustable；不可調節的

nonadjustable modulating spring；不可調節的調制彈簧

nonaftercooled engine；非后冷式發動機

nonangled position；無角度位置

nonasbestos fiber gasket；無石棉纖維襯墊

nonasbestos lining；無石棉襯料

nonconductive material；絕緣材料

nonconductive plunger；不傳導的柱塞

noncooled；未被冷卻的

noncooled flange；未冷卻的法蘭盤

noncorrosive；抗蝕的，不銹的

noncritical fault非臨界誤差[故障]

noncurrent pump；非通用式泵

noncurrent steering clutch；非通用轉向離合器

noncurrent thermostat housing；非通用節溫器外殼

noncurrent water lines group；非通用水管組件

nondetergent；未凈化的

nondetergent oil；未凈化油

nondetergent petroleum oil；未凈化石油(潤滑油)

nondifferential；無差別的，不可微分的

nondriven；非傳[主]動的

nonelectric governor；非電調節器

nonempty cylinder；有載油[氣]缸

nonenergized；未激勵的

nonessential component；非基本部件

nonextreme pressure；非極限壓力

nonfactory connection；非商行在國外代理處的來往關系

nonferrous；非鐵的

nonferrous particle；非鐵顆粒

nonflammable；不可[易]燃的

nonflammable cleaning solvent；不可[易]燃洗滌(溶)劑

nonflammable fluid；不可[易]燃流體

nonflammable liquid；不可[易]燃液體

nonflammable solvent；不可[易]燃溶劑

nonfreezing；耐寒的，不凍的

nonfreezing window washer solvent；耐寒的窗用洗滌劑

nonfunctional；非功能的

nonfunctional knob；非功能按鈕

nongroove side；無凹槽邊

nonhardening sealing compound；非硬化的密封膠

nonhydrostatic drive machine；非靜液壓驅動機械

noninching signal；非漸進信號

noninsulated screw；非絕緣螺釘

noninsulated terminal；非絕緣接線柱

nonlatching type；非閉鎖式

nonload reaction無載反應

nonlubricated；未加潤滑油的

nonmagnetic ring；非磁化環

nonmarking tire；無標記輪胎

nonmating surface；非配合表面

nonmetal ring；非金屬環

nonmetallic；非金屬的

nonmetallic cage；非金屬罩

nonmetallic guard；非金屬護板

nonmetallic hose；非金屬軟管

nonmetallic impeller；非金屬葉輪

nonmetallic material；非金屬材料

nonmetallic surface；非金屬表面

nonmetric；非公制的

nonmetric fastener；非公制緊固件

nonmodulated；非調制的

nonparallel unit；非平行裝置

nonpressurized；不加壓的

nonrecessed；未開槽的

nonrechargeable alkaline battery；不可再充電的堿性蓄電池

nonrestrained track；不受限制的軌道[履帶]

nonreturn valve止回閥

nonrotating；不回轉的

nonrotating ring gear；不回轉的齒圈

nonrotating swashplate；不旋轉的斜板

nonroutine maintenance；非例行維護

nonrunning engine；非工作狀態下發動機

nonserviceable；不耐用的

nonserviceable item；不耐用的零件

nonservo governor；非伺服調速器

nonservo system；非伺服系統

nonskid；不滑動的

nonspacer plate oilpan；無隔板油底殼

nonspinning wheel；不自旋輪

nonstall；未失速

nonstall load sensing condition；未失速載荷信號傳感情況

nonstandard tap；非標準開關

nonsteer position；非轉向位置

nonsteered axle；非轉向軸

nonsudsing detergent；無泡沫洗滌劑

nonsudsing household detergent；無泡沫家用洗滌劑

nontechnical engine evaluation service tool；非技術評定的發動機維修工具

nonthreaded clamp；無螺紋式夾緊裝置

nonvalved nipple；不帶閥的管接頭

nonvibrating part；非振動零件

nonvolatile memory；非易失[永久性]存儲器

norm；標準，定額

norm bkr；標準開關[斷路器]

normal；標準的，規定的

normal limit switch；標準限位開關

normal mode；標準模式

normal mode operation；標準模式操作

normal source light；標準電源燈

normal source pilot light；標準電源指示燈

normal source switch；標準電源開關

normal source trip alarm lamp；標準電源自動跳閘報警燈

normal source undervoltage pc card；標準電源電壓不足時的印刷電路板

normal source voltage monitoring card；標準電源電壓監控板

normal stop switch；標準的停止開關

normally；正常地

normally closed connection；常閉合的連接

normally closed position；常閉合位置

north；北方

north america；北美洲

north american directory；北美號碼簿

north american rating；北美定額

nose；頭部，尖端，噴嘴

nose bar；尖頭桿

nose bar installation；尖頭桿安裝

nose clearance；噴嘴間隙

nose housing；噴嘴外殼

nose piece；測頭管殼

nospin differential；非自旋差速器

nospin differential assembly；非自旋差速器總成

nospin differential group；非自旋差速器組件

nospin differential test；非自旋差速器試驗

nospin differential testing and adjusting；非自旋差速器試驗與調整

notable；值得注意的，顯著的

notation；符號，標志

notch；凹槽，切口

notch end；切口端

notched end；開槽端

notched part；開槽零件

notched side；開槽邊

notched washer；開口墊圈

note；注，筆記

nothing；什么也沒有

notice；注意

notice plate；通知板

notice tag；通知卡，注意標簽

noticeable；顯著的

noticeable change；顯著變化

noticeable increase；顯著增加

noticeable reduction；顯著減少

notification；通知

november；十一月

now；現在

nozzle；噴嘴，噴管

nozzle adapter；噴嘴接頭

nozzle adjustment；噴嘴調節

nozzle application；噴管的使用

nozzle applicator；噴管灑施機

nozzle assembly；噴嘴總成

nozzle assembly adapter；噴嘴總成連接器

nozzle ball valve；噴嘴球閥

nozzle bleed screw；噴管放油螺釘

nozzle body；噴嘴體

nozzle bottom face；噴嘴底面

nozzle cap；噴嘴帽

nozzle cap installation；噴嘴帽安裝

nozzle cap nut；噴嘴帽螺母

nozzle clamp；噴嘴夾子

nozzle clamp bolt；噴嘴夾緊螺栓

nozzle cleaning；噴嘴的清洗

nozzle cleaning kit；噴嘴清洗成套工具

nozzle cleaning tool group；噴嘴清洗工具組件

nozzle condition；噴嘴狀態

nozzle cone；噴嘴錐頭

nozzle end；噴嘴端部

nozzle extension；噴管的加長

nozzle groove；噴嘴凹槽

nozzle group；噴嘴組件

nozzle holder；噴嘴座

nozzle holder spring；噴嘴座彈簧

nozzle holding tool噴嘴固定工具

nozzle hole；噴嘴孔

nozzle insert；噴嘴襯墊

nozzle installation；噴嘴安裝

nozzle leak；噴嘴泄漏

nozzle needle；噴嘴針閥

nozzle needle stem；噴嘴針閥桿

nozzle nut；噴嘴螺帽

nozzle opening pressure噴嘴開啟壓力

nozzle orifice；噴嘴孔

nozzle performance；噴嘴性能

nozzle preparation；噴嘴預調

nozzle pressure；噴嘴壓力

nozzle puller；噴嘴拆卸工具[拉出器]

nozzle puller gp；噴嘴拆卸工具組件

nozzle puller group；噴嘴拆卸工具組件

nozzle retainer；噴嘴固定座

nozzle seat；噴嘴座

nozzle setting pressure；噴嘴調定壓力

nozzle size；噴嘴尺寸

nozzle size table；噴嘴尺寸表

nozzle spray pattern check；噴嘴噴霧圖形檢驗

nozzle spring；噴嘴彈簧

nozzle stem；噴嘴(管)桿

nozzle test；噴嘴試驗

nozzle test procedure；噴嘴試驗步驟

nozzle test record；噴嘴試驗記錄

nozzle test tool；噴嘴試驗工具

nozzle tester；噴嘴試驗器

nozzle tester group；噴嘴試驗器組件

nozzle tester preparation；噴嘴試驗器預準備

nozzle testing group；噴嘴試驗組合[組件]

nozzle tip；噴嘴尖頭

nozzle tip assembly；噴嘴尖頭總成

nozzle tip orifice；噴嘴尖頭小孔

nozzle valve；噴嘴閥門

npn；半導體[晶體管]

npn type transistor；晶體管

npr；噪聲功率比

nps；美國標準直管螺紋

npsf；美國標準管道內園柱螺紋

npsf plug；美國標準管道內園柱螺塞

npsf tap；美國標準管道內園柱旋塞

npsf thread；美國標準管道內園柱螺紋

npsm；美國標準管道機械連接園柱螺紋

npt；美國標準錐管螺紋

npt air start device；美國標準錐管螺紋氣壓起動裝置

npt bulkhead fitting；美國標準錐管螺紋隔板接頭

npt ext thd；美國標準錐管螺紋外螺紋

npt external thread；美國標準錐管螺紋外螺紋

npt female fitting；美國標準錐管螺紋內接頭

npt hole；美國標準錐管螺紋孔

npt int；美國標準錐管螺紋內孔

npt int thd；美國標準錐管螺紋內孔螺紋

npt internal thread；美國標準錐管螺紋內螺紋

npt male fitting；美國標準錐管螺紋外接頭

npt nipple；美國標準錐管螺紋管接頭

npt pipe fitting；美國標準錐管螺紋管接頭

npt pipe nipple；美國標準錐管螺紋管螺紋接頭

npt plug；美國標準錐管螺紋塞

npt port；美國標準錐管螺紋孔

npt socket head plug；美國標準錐管螺紋內六角螺塞

npt thread；美國標準錐管螺紋

npt-to-metric adapter；美國標準錐管螺紋到公制轉接器

nptf；美國標準錐管螺紋

nptf case drain；殼體排放口美國標準錐管螺紋

nptf connection；美國標準錐管螺紋連接

nptf female thread；美國標準錐管陰螺紋

nptf hole；美國標準錐管螺紋孔

nptf internal pipe thread；美國標準錐管螺紋管內螺紋

nptf oil pressure tap；美國標準錐管螺紋油壓旋塞

nptf oil return；美國標準錐管螺紋回油(管)

nptf pipe tap；美國標準錐管螺紋管嘴

nptf pipe thread；美國標準錐管螺紋

nptf thd；美國標準錐管螺紋

nptf thread；美國標準錐管螺紋

ns；(美國)固定特種(螺紋)

ns switch；(美國)固定特種螺紋的轉換

nsfs； 有源性能標準

nss；衛星導航系統[供氮系統]

nudge；輕推

nuisance trip；障礙跳閘[松開]

nuisance warning；障礙警告

null；零位[空行]

null adjustment screw；零位調節螺釘

null dead band；零位不工作區域[死區]

null point；零位點

null position；零位位置

null screw；零位螺釘

nulling mechanism；指零機構

num；號(數)

number；數字，號數

number code；數碼

number identification；數字識別

number one crankshaft throw；第一號曲軸曲柄

number one fuel pump outlet；第一號燃油泵排出口

number plate；數字盤

number sequence；數序

number two boom section；第二動臂截面

numbered；已被編號的

numbered end；已編號端面

numbered sequence；已編號順序

numbered side；已編號側面

numbering sequence；編號順序

numeric；數字(的)

numerical；數的

numerical code；數字編碼

numerical gauge；數字儀表

numerical order；號數

numerical parts record；零件數量記錄

numerical sequence；數序

numerous；大批的

nurse；精心管理[使用]

nut；螺帽(母)

nut and lock assembly；螺帽與鎖定裝置

nut assembly；螺帽組件

nut collar；螺帽卡圈

nut cover；螺帽遮蓋

nut end；螺帽端面

nut face；螺帽表面

nut installation；螺帽裝配

nut lip；螺帽(凸)緣

nut lock；螺帽鎖定

nut removal；螺帽卸除

nut seat；螺母座

nut seat area；螺母座面積

nut seat face；螺母座工作面

nut thread；螺帽螺紋

nut tightening sequence；螺帽擰緊順序

nut torque；螺帽力矩

nut-to-body；螺帽對機體

nylon；尼龍

nylon ball；尼龍球

nylon bearing；尼龍軸承

nylon body；尼龍機體

nylon bristle；尼龍硬毛

nylon brush；尼龍刷子

nylon bushing；尼龍襯套

nylon cleaning brush；尼龍清潔刷子

nylon coating尼龍涂層

nylon eyelet；尼龍小孔

nylon filter；尼龍濾清器

nylon gasket；尼龍襯墊

nylon material；尼龍材料

nylon pad；尼龍襯墊

nylon pulley；尼龍滑輪[帶輪]

nylon ring；尼龍環

nylon seal；尼龍密封

nylon sling；尼龍吊環

nylon strap；尼龍帶

nylon thrust pad；尼龍推力緩沖墊

nylon tubing；尼龍管道(系統)

nylon vacuum fitting；尼龍真空裝置配件[零件]

nylon wear band；尼龍耐磨帶

nylon webbing；尼龍帶子

o ring retainer；護座O型圈

o-ring；O型密封圈

o-ring adapter；連接器O型圈

o-ring assembly；O型圈總成

o-ring assembly compound；O型圈總成復合體

o-ring compound；O型圈復合體

o-ring compression；O型圈的壓縮

o-ring connector；連接器O型圈

o-ring coupler；聯軸節O型圈

o-ring cover；蓋O型圈

o-ring elbow；彎管接頭O型圈

o-ring face seal；端面密封O型圈

o-ring face seal adapter；連接器端面密封O型圈

o-ring face seal fitting；端面密封O型圈裝配

o-ring face seal fitting nut；端面密封O型圈裝配螺帽

o-ring face seal joint；端面密封O型圈連接

o-ring fitting；O型圈裝配

o-ring fitting end；O型圈裝配端面

o-ring groove；O型圈槽

o-ring kit；O型圈裝卸成套工具

o-ring ledge；O型圈凸耳

o-ring plug；塞O型圈

o-ring port teeT形管口O型圈

o-ring reducer；減壓器O型圈

o-ring seal；O型圈密封

o-ring seal engagement；O型圈密封結合

o-ring seal failure；O型圈密封失效

o-ring seal gasket；密封襯墊O型圈

o-ring seal groove；O型密封圈槽

o-ring seal head；蓋部O型密封圈

o-ring seal lip；O型密封圈唇部

o-ring seal nut；O型密封圈螺母

o-ring seal removal；O型密封圈拆卸

o-ring seal replacement；O型密封圈更換

o-ring seal resistance；O型密封圈阻力

o-ring seat；O型圈座

o-ring type device；帶有O型圈的裝置

o-ring type fitting；帶有O型圈的裝置

o-ring type plug；帶有O型圈塞子

o-ring type seat；帶有O型圈座

obey；執行[服從]

object；物體[目標]

objectionable vibration；有害振動

objective；目標[任務]

obligation；責任[契約]

obscure；模糊的，暗的

observation；觀察，檢查

observed line current；被測的線電流

observer；觀測者

obsolete；過時的

obstacle；障礙物，雷達目標

obstacle scanner；雷達目標掃描裝置

obstacle scanner linkage；雷達目標掃描裝置聯桿

obstacle scanner pivot；；雷達目標掃描裝置樞樞

obstructed阻塞的

obtainable；能獲得的

obtained data；獲得的數據

obvious；明顯的

obviously；明顯的

occasion；時機，場合

occasional bubble；偶見的氣泡

occupational safety and health administration；職業安全及衛生管理局

occurrence；發生，出現

ocl；操作檢查表

ocr；光學符號識別

oct；八角形的，十月

octagon；八角形

octagon size；八角形尺寸

octagon socket；八角形套管

octagonal；八角形的

octane；辛烷值

octane rating；額定率烷值

october；十月

ocv；xxx

od；外徑

odd number；奇數

odometer；里程表

odometer distance；里程表行程

odor；氣味，臭味

odorless；無氣味的

oem；原設備制造廠

oem crank relay；原設備制造廠曲柄(搖動)繼電器

oem dealer；原設備制造廠代理商

oem factory；原設備制造廠

oem ground；原設備制造廠廠區

oem harness；原設備制造廠導線束

oem manufacturer；原設備制造廠制造者

oem recommendation；原設備制造廠的建議

oem recommended procedure；原設備制造廠建議的程序

oem responsibility；原設備制造廠的職責

oem retarder electronics；原設備制造廠減速器電子線路

oem specification；原設備制造廠技術規格

oem supplied linkage；原設備制造廠提供的連接裝置

oem supplied retarder electronics；原設備制造廠提供的減速器電子線路

oem supplied wiring；原設備制造廠提供的導線

oem systems troubleshooting；原設備制造廠的系統故障排除

oem truck configuration；原設備制造廠載重車外形[結構]

oem truck manufacturer；原設備制造廠載重車生產者

oem truck system responsibility ；原設備制造廠載重車系統的可靠性

oem truck wiring diagram；原設備制造廠載重車線路圖

oem vehicle manual；原設備制造廠車輛手器

oem wire；原設備制造廠導線

oem wiring schematic；原設備制造廠線路圖

off-center；偏心

off-center loading；偏心載荷

off-center placement；偏心布置

off-engine；在發動機之外的

off-engine timing dimension；在發動機之外的定時尺寸

off-highway；非公路的

off-highway tractor；非公路的拖拉機

off-highway truck；非公路的載重車

off-highway truck differential；非載重車差速器

off-highway truck final drive first reduction planetary assembly；非公路載重車最終傳勸第一線行星減速裝置總成

off-highway truck front axle；非公路載重車前軸

off-highway truck front suspension cylinder；非載重車前懸掛油缸

off-highway truck operation maintenance manual；非載重車操作保養手冊

off-highway truck payload measurement system；非載重車有效負載測試系統

off-highway truck wheel；非載重車車輪

off-test-auto-engine start；發動機停止-試驗-自動控制-起動

off/lo/hi；斷開/低/高

off/locked；斷開/鎖止

off/on；斷開/接通

off/on/start key switch；斷開/接通/起動鑰匙開關

off/reset；斷開/重調[復位]

off/reset signal；斷開/重調[復位]信號

offer；提供，企圖

office；辦公室

offset adapter；偏置(心)連接器

offset boom；偏置動臂

offset stick；偏置斗桿

offshore crane；海上起重機

ohm；歐姆

ohm load adjusting potentiometer；歐姆加載調節電位計

ohm per foot；歐姆/英尺

ohm per meter；歐姆/米

ohmmeter；電阻表

ohmmeter lead；電阻表導線

ohmmeter reading；電阻表讀數

ohmmeter scale；電阻表刻度(盤)

oht；電阻表

oht component；電阻表部件

oil；油，潤滑油

oil aeration；充油

oil analysis；油的分析

oil analysis program；油的分析程序

oil analysis requirement；油的分析要求

oil back pressure；油的背壓力

oil base cleaner；基油濾清器

oil bath；油槽

oil bleed hole；泄油孔

oil bleeder screw；油泄放器螺釘

oil bore；油腔

oil brand；油牌號

oil breather；油通氣裝置[呼吸器]

oil breather cap；油通氣裝置蓋

oil breather group；油通氣裝置組件

oil bypass line；油的旁通管路

oil bypass valve；油的旁通閥

oil capacity；油的容積[量]

oil cavity；油腔

oil chamber；油室

oil change；換油

oil change interval；換油周期

oil charging equipment；加油設備

oil charging procedure；加油步驟

oil charging tool；加油工具

oil check plug；油檢查塞

oil circuit；油回路

oil circulation；油循環

oil clutch pump；離合器油泵

oil clutch pump pulley；離合器油泵皮帶輪

oil coking；油焦化

oil coking problem；油焦化問題

oil cold zone；油的冷卻區

oil collector cup；集油杯

oil company；石油公司

oil compartment；油箱[艙]

oil compensation；油補償[補充]

oil condition；油的狀態

oil condition analysis；油的狀態分析

oil condition test；油的狀態測試

oil connection fitting；油管接頭安裝

oil consumption；油耗

oil consumption rate；耗油率

oil container；貯油器

oil contamination；油污染

oil control；(潤滑)油控制

oil control piston ring；活塞油環

oil control ring；油環

oil control ring gap；油環開口間隙

oil control ring groove；油環環槽

oil coolant；油冷卻劑[液]

oil cooled；油冷卻

oil cooled brake bleed valve；油冷式制動器泄放閥

oil cooled cylinder head；油冷式缸蓋

oil cooled disc brake；油冷式盤[片]式制動器

oil cooled drive group；油冷式傳動組件

oil cooled multi-disc brake；油冷式多片式制動器

oil cooled unit；油冷設備

oil cooler；油冷卻器

oil cooler assembly；油冷卻器總成

oil cooler base；油冷卻器基座

oil cooler base bypass valve；油冷卻器基座旁通閥

oil cooler body；油冷卻器(殼)體

oil cooler bonnet；油冷卻器罩[蓋]

oil cooler bracket；油冷卻器支架

oil cooler bypass；油冷卻器旁通管

oil cooler bypass elbow；油冷卻器旁通管彎頭

oil cooler bypass line；油冷卻器旁通管路

oil cooler bypass valve；油冷卻器旁通閥

oil cooler bypass valve assembly；油冷卻器旁通閥總成

oil cooler capacity；油冷卻器容量

oil cooler cavity；油冷卻器內腔

oil cooler check valve；油冷卻器單向閥

oil cooler circuit；油冷卻器回路

oil cooler connection；油冷卻器連接

oil cooler core；油冷卻器芯子

oil cooler core assembly；油冷卻器芯子總成

oil cooler cover；油冷卻器護罩

oil cooler drain plug；油冷卻器排油塞

oil cooler external inlet line；油冷卻器外部進油管路

oil cooler fan motor；油冷卻器風扇電機

oil cooler fin；油冷卻器散熱片

oil cooler flow；油冷卻器流量

oil cooler gasket；油冷卻器密封墊

oil cooler group；油冷卻器組件

oil cooler heat exchanger；油冷卻器熱交換器

oil cooler inlet；油冷卻器進口

oil cooler inlet pressure；油冷卻器進口壓力

oil cooler inlet relief valve；油冷卻器進口安全閥

oil cooler leak；油冷卻器泄漏

oil cooler line；油冷卻器管路

oil cooler lines gp；油冷卻器管路組件

oil cooler lines group；油冷卻器管路組件

oil cooler location；油冷卻器位置

oil cooler oil flow；油冷卻器油流量

oil cooler outlet；油冷卻器出口

oil cooler output line；油冷卻器輸出管路

oil cooler performance；油冷卻器性能

oil cooler pressure drop；油冷卻器壓力降[差]

oil cooler pump；油冷卻器泵

oil cooler relief valve；油冷卻器安全閥

oil cooler return oil；油冷卻器回油

oil cooler return port；油冷卻器回油孔

oil cooler return screen；油冷卻器回油濾網

oil cooler schematic；油冷卻器簡圖

oil cooler screen；油冷卻器濾網

oil cooler seal；油冷卻器密封

oil cooler supply line；油冷卻器供水管線

oil cooler supply valve；油冷卻器供水閥

oil cooler system；油冷卻器系統

oil cooler temperature regulator；油冷卻器溫度調節器

oil cooler tube；油冷卻器管

oil cooler upper bracket；油冷卻器上托架

oil cooler water；油冷卻器水

oil cooler water inlet tube；油冷卻器進水管

oil cooler water outlet tube；油冷卻器出水管

oil cooler water temperature；油冷卻器水溫

oil cooler water temperature range；油冷卻器水溫范圍

oil cooler water temperature reading；油冷卻器水溫讀數

oil cooling；油冷卻

oil cooling chamber；油冷卻室

oil cooling jet assembly；油冷卻噴嘴總成

oil cooling system；油冷卻系統

oil cover relief valve；油罩蓋安全閥

oil cross hole；十字[交叉]油孔

oil cup；油杯

oil deflector；導油板

oil degradation；油失效

oil delivery；油的輸送

oil demand；所需用油量

oil dilution；油稀釋

oil dipstick；油尺

oil distribution；配油

oil distribution groove；配油槽[溝]

oil distribution tee；配油三通管

oil distributor；配油器

oil drain；排油

oil drain access cover；排油檢視蓋

oil drain adapter；排油管接頭

oil drain adapter assembly；排油管接頭總成

oil drain cart；排油車

oil drain gasket；排油密封墊

oil drain hole；排油孔

oil drain hose；排油軟管

oil drain interval；排油時間間隔[周期]

oil drain line；排油管路

oil drain passage；排油通道

oil drain plug；排油塞

oil drain plug cover；排油塞蓋

oil drain port；排油孔

oil drain tray group；排油槽組件

oil drain tube；排油管

oil drain tube assembly；排油管總成

oil drain valve；排油閥

oil drain valve cover；排油閥蓋

oil drain valve plug；排油閥塞

oil element；油成份

oil end；油終端[剩油]

oil feed；供油

oil feed adjusting screw；供油調節螺釘

oil feed hole；供油孔

oil field；油田

oil field hoisting；油田起重機

oil field mechanical drilling；油田機械鉆井

oil field mechanical pumping；油田機械抽油

oil field well servicing；油田井維護[保養]

oil fill/drain plug；充/排油塞

oil filled cylinder；充油油缸

oil filled gauge；充油測量儀

oil filler；加油器

oil filler base assembly；加油器基座總成

oil filler breather；加油通氣裝置

oil filler cap；加油器帽

oil filler cover；加油器蓋

oil filler cup；加油器杯

oil filler group；加油器組件

oil filler hasp；加油器搭扣

oil filler neck tube；加油器頸管

oil filler pipe；加油器管

oil filler plug；加油器塞

oil filler plug hole；加油器塞孔

oil filler strainer；加油器濾網

oil filler tube；加油器管

oil filler tube assembly；加油器管總成

oil filler tube elbow；加油器管彎頭

oil film；油膜

oil film thickness；油膜厚度

oil filter；濾油器[機油濾清器]

oil filter adapter；濾油器(轉換)接頭

oil filter assembly；濾油器總成

oil filter assembly installation；濾油器總成的安裝

oil filter bank；濾油器組

oil filter base；濾油器座

oil filter base assembly；濾油器座總成

oil filter base assembly stud；濾油器座總成螺柱

oil filter base group；濾油器座組件

oil filter base stud；濾油器座螺柱

oil filter bypass；濾油器旁(通)路

oil filter bypass element；濾油器旁(通)路濾芯

oil filter bypass indicator；濾油器旁(通)路指示器

oil filter bypass pressure switch；濾油器旁路壓力開關

oil filter bypass return port；濾油器旁路回油口

oil filter bypass switch circuit；濾油器旁路開關回路

oil filter bypass valve；濾油器旁通閥

oil filter bypass valve setting；濾油器旁通閥調定

oil filter cap assembly；濾油器帽總成

oil filter component；濾油器部件

oil filter construction；濾油器結構

oil filter cover；濾油器蓋

oil filter cutter；濾油器切刀

oil filter differential gauge；濾油器差(微)壓計

oil filter differential pressure；濾油器壓差

oil filter differential pressure gauge；濾油器壓差(量)計

oil filter drain plug；濾油器排油塞

oil filter element；濾油器濾芯

oil filter element gasket seal surface；濾油器濾芯襯墊密封表面

oil filter element mounting base；濾油器濾芯安裝座

oil filter element removal instruction；濾油器濾芯拆除說明

oil filter element replacement instruction；濾油器濾芯更換說明

oil filter external line；濾油器外部管路

oil filter gasket；濾油器襯墊

oil filter group；濾油器組件

oil filter group valve；濾油器組件閥

oil filter head；濾油器頂蓋

oil filter housing；濾油器殼體

oil filter housing adapter；濾油器殼體連接器

oil filter housing assembly；濾油器殼體總成

oil filter housing drain valve；濾油器殼體排油閥

oil filter housing support；濾油器殼體支架

oil filter inlet supply tube；濾油器進口油管

oil filter inspection；濾油器檢驗

oil filter location；濾油器位置

oil filter mounting stud；濾油器固定螺柱

oil filter plug；濾油器塞

oil filter return port；濾油器回油口

oil filter seal；濾油器密封

oil filter strap wrench；濾油器板扳手

oil filter switch；濾油器開關

oil filter temperature switch；濾油器溫度開關

oil filter tube；濾油器管

oil filters bypass valve；濾油器旁通閥

oil flow；油流量

oil flow check valve；油流單向閥

oil flow circuit；油流動回路

oil flow demand；對油流量的需求

oil flow direction；油流動方向

oil flow feed adjusting screw；供油量調節螺釘

oil flow gauge；油流量計

oil flow passage；油流動通道

oil flow priority；優先油流

oil flow rate；油流動速率[變化率]

oil flow test；油流量測試

oil flywheel clutch；油控飛輪離合器

oil fog；油霧

oil formulation；油的成份[組成]

oil gallery；油溝[回油孔]

oil gallery connector；油溝連接管

oil gallery plug；回油孔塞

oil gasket；油密封墊

oil gauge assembly；油壓計總成

oil gauge tube；油壓計管

oil grade；油等級

oil groove；油槽

oil groove depth；油槽深度

oil groove side；油槽邊

oil guideline；油標志線

oil heater；油加熱器

oil hole；油孔

oil hole boss；油孔凸臺

oil hole opening；油孔開口

oil hole orientation；油孔定位

oil hose；油軟管

oil hose assembly；油軟管總成

oil inlet；進油口

oil inlet flow；進油口流量

oil inlet line；進油口管路

oil inlet opening；進油口

oil inlet passage；進油通道

oil inlet port；進油孔口

oil inlet/outlet port；油進口/出口孔

oil interruption；油中斷

oil jet；噴油嘴

oil jet cooling tube；噴油嘴冷卻管

oil jet tube；噴油管

oil leak；油泄漏

oil leakage；油泄漏

oil leakage test；油泄漏測試         

oil level；油位[面]

oil level cap assembly；油位蓋總成

oil level check；油位檢查

oil level check plug；油位檢查塞

oil level contactor；油位接觸器

oil level contactor group；油位接觸器組件

oil level control schematic；油位控制簡圖

oil level dipstick；油位測量尺

oil level gauge；油位計

oil level gauge assembly；油位計總成

oil level gauge group；油位計組件

oil level gauge mark；油位計標記

oil level gauge marking；油位計標記

oil level gauge tube；油位計管

oil level guard assembly；油位限止器總成

oil level guide group；油位指示組件

oil level hole；油位孔

oil level indicator；油位指示器

oil level information；油位資料

oil level inspection cap；油位觀察蓋

oil level inspection plug；油位檢測塞

oil level mark；油位標記

oil level plug；油位塞

oil level reading；油位讀數

oil level regulator；油位(自動)調節器

oil level regulator group；油位(自動)調節器組件

oil level sensor；油位傳感器

oil level sight gauge；油位觀測計

oil level switch；油位開關

oil level/fill plug；油位/注油塞

oil light；油燃點

oil line；油管路

oil line adapter；油管路接頭

oil line arrangement；油管路布置

oil line connection；油管路連接

oil line connector；油管路接頭

oil line hose；油管路軟管

oil line identification；油管路識別

oil line restriction；油管阻力

oil lines group；油管路組件

oil loss；油損失

oil lubricant level；潤滑油面

oil lubricated wheel bearing；油潤滑的輪軸承

oil lubrication schematic；油潤滑簡圖

oil makeup operation；油的補給操作

oil manifold；油岐管[總管]

oil manifold plug；油岐管塞

oil manifold pressure；油岐管壓力

oil manifold test location；油岐管測試位置

oil metering section；油測量部分[部門]

oil mist；油霧

oil mist detector alarm；油霧檢測器報警

oil mixture；油的混合物[混合油]

oil operating pressure；油工作壓力

oil operating temperature；油工作溫度

oil outlet；油出口

oil outlet cover；油出口蓋

oil outlet dowel；油出口定位銷

oil outlet passage；油出口通道

oil outlet port；油出口孔

oil output；油輸出

oil overflow；油溢流

oil overheating；油過熱

oil oxidation；油氧化

oil pan；油盤[底殼]

oil pan area；油盤面積

oil pan baffle；油盤擋板

oil pan bolt；油盤螺栓

oil pan bracket；油盤托架

oil pan drain；油盤排油

oil pan drain cover；油盤排油口蓋

oil pan drain opening；油盤排油口

oil pan drain plug；油盤排油塞

oil pan fastener group；油盤緊固件組件

oil pan gasket；油盤密封墊

oil pan gasket surface；油盤密封墊表面

oil pan group；油盤組件

oil pan level gauge；油盤油面計

oil pan mating surface；油盤配合表面

oil pan plate；油盤板

oil pan plate assembly；油盤板總成

oil pan plate gasket；油盤板密封墊

oil pan section；油盤截面[部分]

oil pan sump；油盤貯油槽

oil pan sump configuration；油盤貯油槽形狀

oil pan surface；油盤表面

oil particle；油微粒

oil passage；油通道

oil passage angle；油通道角度

oil passage connection；油通道連接

oil passage head end；蓋端油通道

oil passage rod end；活塞桿端油通道

oil passage schematic；油通道簡圖

oil passage slot；油通道縫隙[切口]

oil path；油通路

oil performance；油的性能

oil pickup tube；油(壓力)測量管

oil pipe；油管

oil piston；液壓活塞

oil plate；油盤[板]

oil plug；油塞

oil port；油孔

oil press；油壓機

oil pressure；油壓力

oil pressure adapter group；油壓力轉換器組件

oil pressure alarm；油壓力報警(器)

oil pressure bargraph area；油壓力(統計用)線條圖面積

oil pressure check；油壓力檢查

oil pressure check location；油壓力檢查位置

oil pressure circuit；油壓力回路

oil pressure connection；油壓力連接

oil pressure contactor switch；油壓力接觸器開關

oil pressure curve；油壓力曲線

oil pressure delay；油壓力延遲[滯后]

oil pressure difference；油壓力差

oil pressure differential；油壓力差動(裝置)

oil pressure drop；油壓力降

oil pressure failure circuit；油壓力故障回路

oil pressure fault；油壓力故障

oil pressure gauge；油壓計[表]

oil pressure gauge connection；油壓計連接

oil pressure hole；壓力油孔

oil pressure indicator；油壓力指示器

oil pressure indicator light；油壓力指示器燈

oil pressure input circuit；壓力油輸入回路

oil pressure light；油壓燈

oil pressure line；壓力油管路

oil pressure operating limit；油工作壓力極限

oil pressure protection；油壓保護裝置

oil pressure rating；油壓額定值[額定壓力]

oil pressure reading；油壓力讀數

oil pressure reading range；油壓力讀數范圍

oil pressure relay；油壓力繼電器

oil pressure released brake；油壓松放制動器

oil pressure relief hole；油卸壓孔

oil pressure relief valve；油壓安全閥

oil pressure sender；油壓力傳送器

oil pressure sender assembly；油壓力傳送器總成

oil pressure sending switch；油壓力傳送器開關

oil pressure sending unit；油壓力發送裝置

oil pressure sending unit test；油壓力發送裝置測試

oil pressure sensing group；油壓力傳感組件

oil pressure sensing switch；油壓力傳感開關

oil pressure sensing valve；油壓力傳感閥

oil pressure sensor；油壓力傳感器

oil pressure sensor fault；油壓力傳感器失效

oil pressure sensor signal circuit；油壓力傳感器信號電路

oil pressure sensor test；油壓力傳感器測試

oil pressure sensor unit；油壓力傳感器元件

oil pressure shutdown；油壓力關閉[斷路]

oil pressure shutoff；油壓力關閉[切斷]

oil pressure shutoff system；油壓力關閉系統

oil pressure signal；油壓信號

oil pressure signal voltage；油壓信號電壓

oil pressure signal wire；油壓信號導線

oil pressure solenoid；油壓電磁線圈

oil pressure source；油壓力源

oil pressure speed limiter；壓力油速度限制器

oil pressure step circuit；油壓分級回路

oil pressure step function；油壓力分級作用

oil pressure step switch；油壓力步進開關

oil pressure step switch contact；油壓力步進開關觸點

oil pressure step switch ess；油壓力步進開關電子安全系統

oil pressure summing control system；油壓總控制系統

oil pressure supply；油壓力傳送

oil pressure switch；油壓力開關

oil pressure switch connection；油壓力開關連接

oil pressure switch location；油壓力開關位置

oil pressure switch wire；油壓力開關導線

oil pressure temperature sensor；壓力油溫度傳感器

oil pressure test；油壓力測試

oil pressure test location；油壓力測試位置

oil pressure test plug；油壓力測試塞

oil pressure timer；油壓力定時器

oil pressure valve；油壓力閥

oil pressure/temperature sensor；油壓力/溫度傳感器

oil pressure/temperature transducer；油壓力/溫度傳感器

oil pressure/temperature transducer module；油壓力/溫度傳感器模件

oil priority valve；油優先閥

oil problem；油的故障

oil property；油的性質

oil pump；油泵

oil pump adapter；油泵(轉換)接頭

oil pump bearing；油泵軸承

oil pump bleed line；油泵放油管路

oil pump body；油泵體

oil pump body assembly；油泵體總成

oil pump bolt；油泵螺栓

oil pump bushing；油泵軸襯[軸瓦]

oil pump bypass；油泵旁路

oil pump bypass drain；油泵旁路排油

oil pump bypass valve；油泵旁通閥

oil pump clearance；油泵間隙

oil pump construction；油泵結構

oil pump cover；油泵蓋

oil pump cover assembly；油泵蓋總成

oil pump drive；油泵驅動(裝置)

oil pump drive bearing；油泵驅動軸承

oil pump drive gear；油泵驅動齒輪

oil pump drive housing；油泵驅動箱體

oil pump drive shaft；油泵驅動軸

oil pump drive spline；油泵驅動花鍵軸

oil pump failure；油泵故障

oil pump flange；油泵法蘭盤

oil pump gear；油泵齒輪

oil pump gear rotor tip；油泵齒輪轉子頂部

oil pump group；油泵組件

oil pump housing；油泵殼體

oil pump housing seal；油泵殼體密封

oil pump idler gear；油泵從動[中間]齒輪

oil pump idler gear bearing；油泵從動齒輪軸承

oil pump idler gear bolt；油泵從動齒輪螺栓

oil pump idler gear shaft；油泵從動齒輪軸

oil pump idler shaft；油泵從動輪軸

oil pump inlet；油泵入口

oil pump inlet line；油泵入口管路

oil pump inlet tube；油泵入口管

oil pump input gear；油泵輸入齒輪

oil pump installation；油泵安裝

oil pump mounting bolt；油泵固定螺栓

oil pump o-ring seal；油泵O型密封圈

oil pump outlet；油泵出口

oil pump outlet elbow；油泵出口彎頭

oil pump outlet passage；油泵出口通道

oil pump output；油泵輸出

oil pump output capacity；油泵出能力

oil pump output pressure tap；油泵輸出壓力分接頭

oil pump performance；油泵特性

oil pump pressure；油泵壓力

oil pump pressure regulating valve；油泵壓力調節閥

oil pump relief valve；油泵安全閥

oil pump relief valve assembly；油泵安全閥總成

oil pump rotation；油泵旋轉

oil pump rotor；油泵轉子

oil pump rotor tip；油泵轉子頂端

oil pump screen；油泵濾網

oil pump shaft；油泵軸

oil pump shaft assembly；油泵軸總成

oil pump spacer；油泵隔片

oil pump suction；油泵吸油

oil pump suction bell；油泵吸油罩

oil pump suction line；油泵吸油管路

oil pump suction pipe；油泵吸油管

oil pump suction tube；油泵吸油管

oil pump supply tube；油泵供油管

oil pump system；油泵系統